- Tripp Lite
- Call for next available delivery
Tripp Lite’s APSX4048SW DC-to-AC inverter with automatic line-to-battery transfer and integrated charging system serves as an extended run UPS, a standalone power source or an automotive inverter. Supplies up to 4000 watts of continuous 220, 230 or 240V selectable AC input & output from any 48V DC battery or automotive DC source; 50/60Hz pure sine wave output (hardwired). When hardwire AC input is energized, commercial power passes through to connected equipment and the battery set is recharged via 3 stage, 1/70 amp charging system. In UPS mode, the APS system responds to blackouts and severe voltage fluctuations with a near instantaneous automatic transfer to battery-derived AC output. Includes a set of high current DC input terminals for simple installation (user supplies batteries and cabling - see owner's manual for recommendations). Passes sine wave utility or generator power during battery charging and UPS line power operation, and sine wave AC output in inverter and UPS backup modes. Built-in Automatic Voltage Regulation (AVR) corrects line power AC brownouts and overvoltages without using battery power during battery charging and UPS standby modes. Reliable large transformer design, with frequency control powers resistive electronic loads or large inductive motors, compressors and other items with high current needs on startup. Optional APSRMSW wired remote power switch with full status LEDs provides remote power inverter on/off switching and continuous status information (part# APSRMSW sold separately). Supports an unlimited amount of runtime with any number of user-supplied batteries connected. Highly adaptable to a variety of applications and site conditions with adjustable charger settings for wet/gel battery types and selectable line to battery power transfer voltages.
220,230 or 240V selectable AC input & output from any 48VDC battery or automotive DC source
4000W continuous pure sine wave AC output in inverter mode
Double Boost output supports momentary start-up loads up to 200% of the continuous rating for up to 10 seconds (see specification chart) - OverPower output supports longer duration overloads to 150% for up to 60 seconds
3-stage, selectable 1/70 amp battery charger with adjustable settings for wet/gel battery types
LCD display and 4 membrane selector buttons allow user to configure operation
Automatic overload and thermal (overheating) shutoff
Front panel remote control connector enables remote off/on switching (APSRMSW sold separately)
Load sensing control dial enables adjustable load threshold required to automatically turn the inverter on and off in DC mode as load conditions change
Remote battery temperature sensing connection function prolongs battery life by adjusting the charge float voltage level based on battery temperature
USER INTERFACE, ALERTS & CONTROLS
Front Panel LEDs: LCD offers continuous status information on load percentage (6 levels reported) and battery charge level (7 levels reported).
Switches: (5) memebrane switches allow user to operate and configure unit operation.
Remote Control Capability: Yes
TVSS Grounding: Main grounding lug connects inverter/charger to earth or vehicle chassis ground
9"h x 7.25"w x 22.5"d
Output Receptacles: (1) Hardwire
Input Connection Type: DC INPUT Set of DC bolt-down terminals. AC INPUT Hardwire via built in terminal strip with cover plate
Power Provided: 4000 watt(s)
Frequency Compatibility: 50/60Hz
Continuous Output Capacity: 4000W
Peak Output Capacity: 6000W
Output Nominal Voltage: 220/230/240V
Output Voltage Regulation: LINE POWER (AC) Maintains nominal sine wave output from line power source; INVERTER POWER (AC) Maintains sine wave output of +/-2%
Output Frequency Regulation: 50/60Hz (+/- 0.5Hz)
Pure Sine Wave Output: Yes
Nominal Input Voltages Supported: 220VAC; 230VAC; 240VAC
Recommended Electrical Service: DC INPUT Requires 48VDC input source capable of delivering 120A for the required duration (when used at full continuous capacity - DC requirements increase during OverPower and DoubleBoost operation). For automotive applications, professional hardwire
Maximum Input Current: 120A
Voltage Compatibility: 220; 230; 240VAC
Voltage Compatibility: 48VDC
Expandable Battery Runtime: Runtime is expandable with any number of user supplied wet or gel type batteries
DC System Voltage: 48VDC
Battery Pack Accessory (Optional): 98-121 sealed lead acid battery (optional)
Battery Charge: Selectable 1/70 amp
Voltage Regulation Description: Includes automatic voltage regulation to correct brownouts and overvoltages back to usable levels
Overvoltage Correction: Overvoltages are automatically reduced by 10%
Brownout Correction: Brownouts are automatically boosted by 10% and 20%
LINE / BATTERY TRANSFER
Transfer Time (Line Power to Battery Mode): 20 millisecond (full cycle) / 10 millisecond (half-cycle)
Low Voltage Transfer to Battery Power: In AC "auto" mode, inverter/charger switches to battery mode as line voltage drops 10 to 80V AC (user adjustable).
High Voltage Transfer to Battery Power: In AC "auto" mode, inverter/charger switches to battery mode as line voltage increases 10 to 40V AC (user adjustable).
This product is subject to our return policy. Please see our complete return policy for details.